This process is deemed less involving as compared to other stringed instruments. A bowed psaltery is triangular in shape and made in such a way that it produces diatonic, sharp and flat notes. Its wooden sound box allows the strings attached to be individually played. They come in different designs though more or less the same format.
Constructing this instrument starts on the body frame. Portions to the body frame are usually cut from plywood straight into triangular design and the perimeters clipped using a band saw. The structures are subsequently glued collectively until finally they are into position. As a way to accomplish pressure on the triangle perimeters, a waxed paper jig need to be used, prior to placing a clamp on the edges to assist fitting the frames tightly.
A small size hole is then drilled, just in the center of one side of the plywood. This ought to be at the back of the instrument and can either be left round in shape or made to any other desirable shape. On the triangular top, a pencil line is drawn to mark the straight lines meant for the strings. Pins are used to mark the clear cut locations and to differentiate the points for the notes that they correspond to.
Holes for both the hitch and tuning pins are drilled. Those for the hitch pins should be made vertically at the front edge, while for the turning pins should come at the back. What then follows is a finish to the instrument. It is better to note that the sound comes out perfect if the finish is harder and brittle.
The bridge should then be build by using a piece of hardwood, grooved to the centre of one side of the instrument. The bridge should be in such a position that it provides enough room for the shortest string for vibration and winding as desired. The tops of all pins should be roughed up to enable them hold the strings to be used in place.
Stringing your instrument is the next phase wherein every string is actually threaded via every hitch pin. The strings should then be pulled over the pins then later laid on top of the bridge. These are subsequently looped on top of the tuning pins along with tightened to offer a proper grip.
An electronic tuner is then used to tune the instruments to enable the notes function as needed. They should also be wind counter clockwise around these pins. The natural notes are meant to run upwards on the right side as the sharps and flats run on the left side.
This specific instrument is actually played using a bow which could basically be created by using hardwood and fishing line. The particular hardwood needs a tiny hole on both prolonged ends, although there ought to be a double knot in one of the said holes. The fishing line is what gives the bow its final look. The line is wrapped around and some space left just around the center of the wood.
Constructing this instrument starts on the body frame. Portions to the body frame are usually cut from plywood straight into triangular design and the perimeters clipped using a band saw. The structures are subsequently glued collectively until finally they are into position. As a way to accomplish pressure on the triangle perimeters, a waxed paper jig need to be used, prior to placing a clamp on the edges to assist fitting the frames tightly.
A small size hole is then drilled, just in the center of one side of the plywood. This ought to be at the back of the instrument and can either be left round in shape or made to any other desirable shape. On the triangular top, a pencil line is drawn to mark the straight lines meant for the strings. Pins are used to mark the clear cut locations and to differentiate the points for the notes that they correspond to.
Holes for both the hitch and tuning pins are drilled. Those for the hitch pins should be made vertically at the front edge, while for the turning pins should come at the back. What then follows is a finish to the instrument. It is better to note that the sound comes out perfect if the finish is harder and brittle.
The bridge should then be build by using a piece of hardwood, grooved to the centre of one side of the instrument. The bridge should be in such a position that it provides enough room for the shortest string for vibration and winding as desired. The tops of all pins should be roughed up to enable them hold the strings to be used in place.
Stringing your instrument is the next phase wherein every string is actually threaded via every hitch pin. The strings should then be pulled over the pins then later laid on top of the bridge. These are subsequently looped on top of the tuning pins along with tightened to offer a proper grip.
An electronic tuner is then used to tune the instruments to enable the notes function as needed. They should also be wind counter clockwise around these pins. The natural notes are meant to run upwards on the right side as the sharps and flats run on the left side.
This specific instrument is actually played using a bow which could basically be created by using hardwood and fishing line. The particular hardwood needs a tiny hole on both prolonged ends, although there ought to be a double knot in one of the said holes. The fishing line is what gives the bow its final look. The line is wrapped around and some space left just around the center of the wood.
0 nhận xét:
Post a Comment